pata_hpt{37x|3x2n}: unify mode programming

As these drivers' set_piomode() and set_dmamode() methods are almost
identical, factor out the common hpt{37x|3x2n}_set_mode() function
to be called by both of them, the same as in 'pata_hpt366' driver.

This results in ~5% decrease in the 'pata_hpt37x' driver binary
size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size
(as measured on x86-32).

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 342aaaaf38322604890ab768fca10f2e6ef19dcc..9b191763e6e5bbe3ae9fe1610d5d8d9399ce7c60 100644 (file)
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -24,7 +24,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME       "pata_hpt37x"
-#define DRV_VERSION    "0.6.14"
+#define DRV_VERSION    "0.6.15"
 
 struct hpt_clock {
        u8      xfer_speed;
@@ -384,20 +384,12 @@ static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)
        return ata_sff_prereset(link, deadline);
 }
 
-/**
- *     hpt370_set_piomode              -       PIO setup
- *     @ap: ATA interface
- *     @adev: device on the interface
- *
- *     Perform PIO mode setup.
- */
-
-static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev,
+                           u8 mode)
 {
        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
        u32 addr1, addr2;
-       u32 reg;
-       u32 mode;
+       u32 reg, timing, mask;
        u8 fast;
 
        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -409,11 +401,31 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
        fast |= 0x01;
        pci_write_config_byte(pdev, addr2, fast);
 
+       /* Determine timing mask and find matching mode entry */
+       if (mode < XFER_MW_DMA_0)
+               mask = 0xcfc3ffff;
+       else if (mode < XFER_UDMA_0)
+               mask = 0x31c001ff;
+       else
+               mask = 0x303c0000;
+
+       timing = hpt37x_find_mode(ap, mode);
+
        pci_read_config_dword(pdev, addr1, &reg);
-       mode = hpt37x_find_mode(ap, adev->pio_mode);
-       mode &= 0xCFC3FFFF;     /* Leave DMA bits alone */
-       reg &= ~0xCFC3FFFF;     /* Strip timing bits */
-       pci_write_config_dword(pdev, addr1, reg | mode);
+       reg = (reg & ~mask) | (timing & mask);
+       pci_write_config_dword(pdev, addr1, reg);
+}
+/**
+ *     hpt370_set_piomode              -       PIO setup
+ *     @ap: ATA interface
+ *     @adev: device on the interface
+ *
+ *     Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+       hpt370_set_mode(ap, adev, adev->pio_mode);
 }
 
 /**
@@ -421,33 +433,12 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *     @ap: ATA interface
  *     @adev: Device being configured
  *
- *     Set up the channel for MWDMA or UDMA modes. Much the same as with
- *     PIO, load the mode number and then set MWDMA or UDMA flag.
+ *     Set up the channel for MWDMA or UDMA modes.
  */
 
 static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
-       struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-       u32 addr1, addr2;
-       u32 reg, mode, mask;
-       u8 fast;
-
-       addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-       addr2 = 0x51 + 4 * ap->port_no;
-
-       /* Fast interrupt prediction disable, hold off interrupt disable */
-       pci_read_config_byte(pdev, addr2, &fast);
-       fast &= ~0x02;
-       fast |= 0x01;
-       pci_write_config_byte(pdev, addr2, fast);
-
-       mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
-       pci_read_config_dword(pdev, addr1, &reg);
-       mode = hpt37x_find_mode(ap, adev->dma_mode);
-       mode &= mask;
-       reg &= ~mask;
-       pci_write_config_dword(pdev, addr1, reg | mode);
+       hpt370_set_mode(ap, adev, adev->dma_mode);
 }
 
 /**
@@ -487,20 +478,12 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
        ata_bmdma_stop(qc);
 }
 
-/**
- *     hpt372_set_piomode              -       PIO setup
- *     @ap: ATA interface
- *     @adev: device on the interface
- *
- *     Perform PIO mode setup.
- */
-
-static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev,
+                           u8 mode)
 {
        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
        u32 addr1, addr2;
-       u32 reg;
-       u32 mode;
+       u32 reg, timing, mask;
        u8 fast;
 
        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -511,13 +494,32 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
        fast &= ~0x07;
        pci_write_config_byte(pdev, addr2, fast);
 
+       /* Determine timing mask and find matching mode entry */
+       if (mode < XFER_MW_DMA_0)
+               mask = 0xcfc3ffff;
+       else if (mode < XFER_UDMA_0)
+               mask = 0x31c001ff;
+       else
+               mask = 0x303c0000;
+
+       timing = hpt37x_find_mode(ap, mode);
+
        pci_read_config_dword(pdev, addr1, &reg);
-       mode = hpt37x_find_mode(ap, adev->pio_mode);
+       reg = (reg & ~mask) | (timing & mask);
+       pci_write_config_dword(pdev, addr1, reg);
+}
 
-       printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
-       mode &= 0xCFC3FFFF;     /* Leave DMA bits alone */
-       reg &= ~0xCFC3FFFF;     /* Strip timing bits */
-       pci_write_config_dword(pdev, addr1, reg | mode);
+/**
+ *     hpt372_set_piomode              -       PIO setup
+ *     @ap: ATA interface
+ *     @adev: device on the interface
+ *
+ *     Perform PIO mode setup.
+ */
+
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+       hpt372_set_mode(ap, adev, adev->pio_mode);
 }
 
 /**
@@ -525,33 +527,12 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *     @ap: ATA interface
  *     @adev: Device being configured
  *
- *     Set up the channel for MWDMA or UDMA modes. Much the same as with
- *     PIO, load the mode number and then set MWDMA or UDMA flag.
+ *     Set up the channel for MWDMA or UDMA modes.
  */
 
 static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
-       struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-       u32 addr1, addr2;
-       u32 reg, mode, mask;
-       u8 fast;
-
-       addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-       addr2 = 0x51 + 4 * ap->port_no;
-
-       /* Fast interrupt prediction disable, hold off interrupt disable */
-       pci_read_config_byte(pdev, addr2, &fast);
-       fast &= ~0x07;
-       pci_write_config_byte(pdev, addr2, fast);
-
-       mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
-       pci_read_config_dword(pdev, addr1, &reg);
-       mode = hpt37x_find_mode(ap, adev->dma_mode);
-       printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
-       mode &= mask;
-       reg &= ~mask;
-       pci_write_config_dword(pdev, addr1, reg | mode);
+       hpt372_set_mode(ap, adev, adev->dma_mode);
 }
 
 /**

diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 269b5dbe51bb934b9ba4cf4910dee3a97df724c5..b131c8f824d70b2312b1a7f6bc447e8d9063ebb2 100644 (file)
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -25,7 +25,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME       "pata_hpt3x2n"
-#define DRV_VERSION    "0.3.9"
+#define DRV_VERSION    "0.3.10"
 
 enum {
        HPT_PCI_FAST    =       (1 << 31),
@@ -161,20 +161,12 @@ static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
        return ata_sff_prereset(link, deadline);
 }
 
-/**
- *     hpt3x2n_set_piomode             -       PIO setup
- *     @ap: ATA interface
- *     @adev: device on the interface
- *
- *     Perform PIO mode setup.
- */
-
-static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+                            u8 mode)
 {
        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
        u32 addr1, addr2;
-       u32 reg;
-       u32 mode;
+       u32 reg, timing, mask;
        u8 fast;
 
        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -185,11 +177,32 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
        fast &= ~0x07;
        pci_write_config_byte(pdev, addr2, fast);
 
+       /* Determine timing mask and find matching mode entry */
+       if (mode < XFER_MW_DMA_0)
+               mask = 0xcfc3ffff;
+       else if (mode < XFER_UDMA_0)
+               mask = 0x31c001ff;
+       else
+               mask = 0x303c0000;
+
+       timing = hpt3x2n_find_mode(ap, mode);
+
        pci_read_config_dword(pdev, addr1, &reg);
-       mode = hpt3x2n_find_mode(ap, adev->pio_mode);
-       mode &= 0xCFC3FFFF;     /* Leave DMA bits alone */
-       reg &= ~0xCFC3FFFF;     /* Strip timing bits */
-       pci_write_config_dword(pdev, addr1, reg | mode);
+       reg = (reg & ~mask) | (timing & mask);
+       pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ *     hpt3x2n_set_piomode             -       PIO setup
+ *     @ap: ATA interface
+ *     @adev: device on the interface
+ *
+ *     Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+       hpt3x2n_set_mode(ap, adev, adev->pio_mode);
 }
 
 /**
@@ -197,32 +210,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *     @ap: ATA interface
  *     @adev: Device being configured
  *
- *     Set up the channel for MWDMA or UDMA modes. Much the same as with
- *     PIO, load the mode number and then set MWDMA or UDMA flag.
+ *     Set up the channel for MWDMA or UDMA modes.
  */
 
 static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
-       struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-       u32 addr1, addr2;
-       u32 reg, mode, mask;
-       u8 fast;
-
-       addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-       addr2 = 0x51 + 4 * ap->port_no;
-
-       /* Fast interrupt prediction disable, hold off interrupt disable */
-       pci_read_config_byte(pdev, addr2, &fast);
-       fast &= ~0x07;
-       pci_write_config_byte(pdev, addr2, fast);
-
-       mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
-       pci_read_config_dword(pdev, addr1, &reg);
-       mode = hpt3x2n_find_mode(ap, adev->dma_mode);
-       mode &= mask;
-       reg &= ~mask;
-       pci_write_config_dword(pdev, addr1, reg | mode);
+       hpt3x2n_set_mode(ap, adev, adev->dma_mode);
 }
 
 /**