Blackfin: drop board resources for dead devices (pbx/ad9960)

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 4c594e647eb45d2614784c60caef9115c0bd16dd..03e4a9941f019a3abdcbb5aefcaa7e9e1b878fa7 100644 (file)
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -199,15 +199,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x4, /* send zero */
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
        .enable_dma = 0,
@@ -296,24 +287,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .mode = SPI_MODE_3,
        },
 #endif
-#if defined(CONFIG_PBX)
-       {
-               .modalias = "fxs-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J11_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-       {
-               .modalias = "fxo-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J19_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
        {
                .modalias               = "ad7877",

diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 18b9bd7d7d64e1f0da16480e10a27a222c93b1a0..fdd518c1b87b1074a072b2b309faf5712106387a 100644 (file)
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -495,13 +495,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
        .enable_dma = 0,
@@ -509,15 +502,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x4, /* send zero */
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
        .enable_dma = 0,
@@ -591,15 +575,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad1836_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
                .modalias = "mmc_spi",
@@ -610,24 +585,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .mode = SPI_MODE_3,
        },
 #endif
-#if defined(CONFIG_PBX)
-       {
-               .modalias = "fxs-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J11_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-       {
-               .modalias = "fxo-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J19_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
        {
                .modalias               = "ad7877",

diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 809c7907b6e3a37fe013e7283fbb7237aa95049e..68b4c804364c043b2e81273a6315f3b4091f70c7 100644 (file)
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -263,15 +263,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x4, /* send zero */
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
        .enable_dma = 0,
@@ -376,24 +367,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .mode = SPI_MODE_3,
        },
 #endif
-#if defined(CONFIG_PBX)
-       {
-               .modalias = "fxs-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J11_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-       {
-               .modalias = "fxo-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J19_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
        {
                .modalias               = "ad7877",

diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 617a28738438b35e7d61b3a80161cc98f012fcfd..4ab9cfa74fdd78b3ec7cf11acbdb62ec7727cbc7 100644 (file)
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -512,13 +512,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
        .enable_dma = 0,
@@ -526,15 +519,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x4, /* send zero */
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
        .enable_dma = 0,
@@ -632,15 +616,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad1836_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
                .modalias = "mmc_spi",
@@ -652,24 +627,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_PBX)
-       {
-               .modalias = "fxs-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J11_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-       {
-               .modalias = "fxo-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J19_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
        {
                .modalias               = "ad7877",

diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 1bd8b61e6888c8b592ea69a7789fda4af69b02e9..30ff3c4a3abe1e8ad1224cb63da195b93139e1f9 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -201,15 +201,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x1c04,
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 /* Notice: for blackfin, the speed_hz is the value of register
  * SPI_BAUD, not the real baudrate */
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
@@ -248,23 +239,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_PBX)
-       {
-               .modalias        = "fxs-spi",
-               .max_speed_hz    = 4,
-               .bus_num         = 1,
-               .chip_select     = 3,
-               .controller_data = &spi_si3xxx_chip_info,
-       },
-
-       {
-               .modalias        = "fxo-spi",
-               .max_speed_hz    = 4,
-               .bus_num         = 1,
-               .chip_select     = 2,
-               .controller_data = &spi_si3xxx_chip_info,
-       },
-#endif
 };
 
 /* SPI (0) */

diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index f3dc2830631cc6d01aece18fbec0fb73c476a59d..3954baa00c64c3fbbf29ec031b3a5e688a9ad36e 100644 (file)
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -219,15 +219,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x4, /* send zero */
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 static struct bfin5xx_spi_chip spidev_chip_info = {
        .enable_dma = 0,
@@ -298,25 +289,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_PBX)
-       {
-               .modalias = "fxs-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J11_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-       {
-               .modalias = "fxo-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J19_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-#endif
-
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
        {
                .modalias = "spidev",

diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 3681d2cb40b3ddb9bf0d6b6202481efb52c77130..159e5b2f9e6b7034c5b06244a07765f303c9828b 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
        .enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
                .modalias = "mmc_spi",

diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 3bbe10227bfbc1c76747a582b2d68d9ca3b17947..0d93bbe6d275c11edad119e668f9dfe7605c5d93 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -293,13 +293,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
        .enable_dma = 0,
@@ -366,15 +359,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad1836_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
                .modalias = "mmc_spi",

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index d438ca40bc1240ce9297a39a63048e66547e4d10..d5aabeeb81eea387676521d51a52be96e4a0bf47 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -549,13 +549,6 @@ static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
 #include <linux/input.h>
 #include <linux/input/ad714x.h>
@@ -698,15 +691,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-       .ctl_reg        = 0x4, /* send zero */
-       .enable_dma     = 0,
-       .bits_per_word  = 8,
-       .cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 #include <linux/spi/ad7877.h>
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
@@ -906,16 +890,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
-
 #if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
        {
                .modalias = "ad714x_captouch",
@@ -940,24 +914,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .mode = SPI_MODE_3,
        },
 #endif
-#if defined(CONFIG_PBX)
-       {
-               .modalias = "fxs-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J11_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-       {
-               .modalias = "fxo-spi",
-               .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 8 - CONFIG_J19_JUMPER,
-               .controller_data = &spi_si3xxx_chip_info,
-               .mode = SPI_MODE_3,
-       },
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
        {
                .modalias               = "ad7877",

diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 97a86b4ce96d991a60953be9d735cff12bac6c07..88eade89842e654dba3e972d80dbcbc254418164 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
        .enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
                .modalias = "mmc_spi",

diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index ebb07554fb09e2e4da90410622289c3c3080544d..cedcc3c6b23566a0c643927307014a63f58d1f35 100644 (file)
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -98,13 +98,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-       .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
        .enable_dma = 0,
@@ -146,15 +139,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad1836_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-       {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
                .modalias = "mmc_spi",