]> www.infradead.org Git - users/dwmw2/linux.git/commit
Input: zinitix - do not report shadow fingers
authorLinus Walleij <linus.walleij@linaro.org>
Fri, 4 Mar 2022 21:17:33 +0000 (13:17 -0800)
committerGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Fri, 8 Apr 2022 12:39:48 +0000 (14:39 +0200)
commitef1a6ab36dc3644073736ca5df9f6742a1aa9a64
tree2b2d6faa26ecf34254af5b0f2c74aef90fad8327
parent21680aabc4d3b789e0379c17561d27f9bc8f6d31
Input: zinitix - do not report shadow fingers

[ Upstream commit e941dc13fd3717122207d74539ab95da07ef797f ]

I observed the following problem with the BT404 touch pad
running the Phosh UI:

When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".

After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).

DOWN
  Zinitix-TS 3-0020: finger 0 down (246, 395)
  Zinitix-TS 3-0020: finger 1 up (0, 0)
  Zinitix-TS 3-0020: finger 2 down (246, 395)
  Zinitix-TS 3-0020: finger 3 up (0, 0)
  Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
  Zinitix-TS 3-0020: finger 0 up (246, 395)
  Zinitix-TS 3-0020: finger 2 up (246, 395)
  Zinitix-TS 3-0020: finger 4 up (246, 395)

This is one touch and release: i.e. this is all reported on
touch (down) and release.

There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.

Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.

Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.

Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.

After this my Zinitix BT404 touchscreen report fingers
flawlessly.

The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:

  if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
      touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;

As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/input/touchscreen/zinitix.c