ARM: dts: microchip: sam9x60: Move i2c address/size to dtsi

ARM: dts: microchip: sam9x60: Move i2c address/size to dtsi

These properties are common for all i2c subnodes.  Allows to add i2c device
nodes (like an rtc for example) in other .dts files including
sam9x60.dtsi without requiring to repeat these properties for each i2c
device again and again.

Found on a custom board after adding this in .dts:

    &flx5 {
            atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
            status = "okay";

            i2c5: i2c@600 {
                    pinctrl-0 = <&pinctrl_flx5_default>;
                    status = "okay";

                    pcf8523: rtc@68 {
                            compatible = "nxp,pcf8523";
                            reg = <0x68>;
                    };
            };
    };

… which created a warning like this:

    […]:236.4-17: Warning (reg_format): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
    […]: Warning (pci_device_reg): Failed prerequisite 'reg_format'
    […]: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
    […]: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
    […]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect #address-cells for I2C bus also defined at […]:228.16-238.4
    […]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect #size-cells for I2C bus also defined at […]:228.16-238.4
    […]: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
    […]: Warning (i2c_bus_reg): Failed prerequisite 'i2c_bus_bridge'
    […]: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
    […]:234.19-237.5: Warning (avoid_default_addr_size): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #address-cells value
    […]:234.19-237.5: Warning (avoid_default_addr_size): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #size-cells value
    […]: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
    […]: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'

This probably should have been done with commit 84f23f3284d5 ("ARM: dts:
at91: sam9x60: move flexcom definitions") already, where those
address-cells and size-cells properties were left in the board .dts
files instead of moving them to the dtsi.

Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240528153109.439407-1-ada@thorsis.com
[claudiu.beznea: adjusted commit message as the properties are not
 required anymore]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>